Vestil WL-100 Premium Truck Scissor Dock Lift - 12,000 lb Capacity
Vestil WL-100 Premium Truck Scissor Dock Lift - 12,000 lb Capacity - 6' W × 12' L #MWS Options 1 is backordered and will ship as soon as it is back in stock.
Shipping & Price Match Guarantee
Shipping & Price Match Guarantee
Enjoy Free Shipping on orders over $200 and a Price Match Guarantee!
Find a lower advertised price on an identical, in-stock item from an authorized U.S. retailer within 14 days of purchase? Email support@bluecollarplanet.com with your order number, the competitor's product link, and a screenshot, and we'll match it.
See our Price Match Guarantee Policy for more information)
What is your Return Policy?
What is your Return Policy?
Cancel within 24 hours of placing your order for a full refund.
After 24 hours or once processing begins, a 25% restocking fee applies even before shipping.
Once your order has shipped, our 30-Day Return Policy applies — see Return Policy for full details.
Customer is responsible for return shipping unless the item arrived damaged or defective.
Click Learn more to read our Detailed Return Policy.
Vestil WL-100 Premium Truck Scissor Dock Lift - 12,000 lb Capacity - 6' W × 12' L #MWS Options 1 is backordered and will ship as soon as it is back in stock.
Payment & Security
Payment methods
Shop with confidence - your transactions are SSL-encrypted and your payment details are securely transmitted.
We never store or have access to your credit card information.
Warranty
Warranty Basics▾
FAQs
What is the usable width of the scissor dock lift? ▾
The usable width on WL-100 units can be calculated as follows:
- For lifts with a removable handrail and fixed toe board, subtract 6" from the overall width.
- For lifts with a removable handrail and removable toe board, subtract 7-1/2" from the overall width.
What wiring is required to install the scissor dock lift? ▾
Five minimum 18 AWG wires (or an appropriate hard service cable) are required between the power unit’s control enclosure and the lift’s frame.
The installer or building owner is responsible for the wiring, power unit disconnect, and branch circuit overcurrent and short-circuit protection.
Please refer to the owner’s manual in the PDF section for complete installation details.
For the WL-100 pit depth with the roll-over option, does it impact the lowered height? ▾
Yes. The WL-100 pit depth with the roll-over option increases the lowered height by 2".
Can the WL series be used outside? ▾
Yes, WL-100 lifts are suitable for outdoor use.
Can the WL-TSP option be used with the WL-3HP voltage change option? ▾
No. The WL-TSP must be paired with the standard 6.5 HP motor and cannot be used with the WL-3HP option.
Is the power unit external or internal? ▾
All power units on WL-100 models are external.
What size is the external power unit? ▾
The hydraulic power unit dimensions are 14" W x 33" L x 31" H and include an 8-foot hose.
How much oil will fit into the hydraulic reservoir? ▾
The hydraulic reservoir has a 15-gallon oil capacity.
Let customers speak for us
Was nervous about going with a Katool balancer instead of a Hunter or a Coats but the price difference was hard to ignore!! 4 months in and zero issues!! Accuracy is great, calibration holds well, digital display is clear and easy to read in our shop lighting!!
Replaced a 1995 Rotary that finally needed too much maintenance to keep limping along. The NT-11 has been a step up in every way. Faster lift, smoother hydraulics, more modern safety features. Glad we made the move.
Use this on the cattle operation for cleaning equipment, trailer interiors, and barn cleanup. The Powerease engine has been reliable, the pump holds pressure consistently, the unit is built tough enough to handle being in a barn environment. No regrets going with the cheaper engine option for our use case.
Spent about 2 months researching lifts before pulling the trigger. Read every review I could find on Triumph, Bend Pak, Atlas, Forward. The NT-9 hit the right balance of capacity, build quality, price, and ALI certification for my budget. Installation was challenging but doable for me and a friend. Lifts have run smoothly since day one. Wish I had bought sooner.
Manage a 50000 sq ft warehouse. We needed to re-stripe forklift aisles and safety zones but did not want exhaust fumes from a Honda-powered striper. The RollMaster 1000 was the answer. Manual roller, no fumes, no engine. Slower than a spray machine for sure but for indoor use the trade-off is worth it. Lines look great when you take your time.
The combo discount made it a no brainer. Would have been about $400 more to buy them separate. Both machines have performed well in our shop. Tire changer handles everything we throw at it including some oversize truck tires. Balancer is accurate within a quarter ounce on most wheels. Solid setup for a 2 bay shop.
I'll share a detailed install experience for anyone considering this lift. Concrete in my garage is 4.5 inches thick, rebar reinforced, 25+ years old. Triumph spec calls for 4 inch minimum with a strength rating I had not measured. Decided to drill some test holes and the anchor pull-test came back fine. Install itself took me and a buddy about 6 hours plus another 2 hours for the hydraulic bleed and calibration. Once running its been flawless. 4 months in, dozen plus jobs through it, including some heavy F-250 work. Solid investment for a serious home garage.
Mo helped me with my order, super responsive, answered all my questions about delivery. Unit got here fast and works perfectly. Thank you!
Our cold storage facility cannot have gas-powered equipment running inside for obvious reasons. The RollMaster 5000 lets us re-stripe forklift aisles and safety zones without venting issues. Battery lasts long enough to do a section per charge, recharges overnight.
20 year old Coats finally cracked the tower casting last spring. Looked everywhere for a replacement and the prices on new Coats and Hunter machines are insane. Settled on the KT-T800 after reading every review I could find. Six months in and it has been a workhorse. We do about 25-30 tires a week through it. No regrets at all.
Run a small auto body shop in Michigan. We use the pressure washer for cleaning panels before paint, washing parts, and cleaning the shop bay floors. The 4200 PSI is honestly more pressure than I need most days but the GPM flow rate is what really helps for getting through the work. Honda GX390 starts every time even when the shop heater is off. Reliable piece of equipment.
We have the contract for a regional grocery chain - 14 stores worth of parking lots. The 4600 SP has been our primary striper for 18 months. Self-propel speed control is consistent which gives us cleaner lines, the Honda engine has been bulletproof, and the dual gun option lets us stripe lanes faster than a single gun machine. Heavy investment that has paid off.
Manual line painter, no fumes, no engine. Paints lines. Does it well enough for our small school yard re-marking each summer. Easy to clean, easy to store. No complaints at all.
Slides over our existing forks, gives us the extra reach when we need it for longer pallets, comes back off when we are done. What more can you ask for.
Solid machine for a working tire shop. We do everything from 15 inch passenger tires to 22 inch on heavy half-ton trucks. The assist arm is not always needed but when you need it you really need it. Hangs out of the way when not in use. Build quality feels appropriate for daily commercial work. About 4 months in, no issues so far.
